Anything to do with Fender, Burns and other guitars; also amps, effects units including eTap, plus any other music making accessories
Moderators: David Martin, dave robinson, Iain Purdon, George Geddes
by Stu's Dad » Thu Apr 02, 2020 9:07 pm
If you have a look on Allparts, Axes'r'us or Stewmac Richie, I think you might find what you want there. Look at the tremolo arms for sale and they'll probably say 'for USA' guitars or 'for Japanese and other Asian guitars'. I think one of them at least will give thread sizes too.
-
Stu's Dad
-
- Posts: 409
- Joined: Wed May 22, 2013 3:34 pm
- Full Real Name: Leonard Evans
by RogerCook » Thu Apr 02, 2020 9:57 pm
Most Japanese blocks will have a M5 (metric thread). However I have one that has a 10-32 thread! Have you got a M5 screw that you could try in it? Be careful though as the metric screw will go into the imperial tapping although it will probably be quite tight.
-
RogerCook
-
- Posts: 498
- Joined: Thu Sep 17, 2009 9:56 am
- Full Real Name: Roger Cook
by Uncle Fiesta » Sat Apr 04, 2020 2:48 pm
Pretty sure it's 5mm - USA and MIM use imperial sizes.
-
Uncle Fiesta
-
- Posts: 1189
- Joined: Fri Apr 27, 2012 11:31 pm
- Location: near Gainsborough, England
- Full Real Name: Steve Tebble
by dave robinson » Sun Apr 05, 2020 10:09 am
Uncle Fiesta wrote:Pretty sure it's 5mm - USA and MIM use imperial sizes.
Thanks for clearing that up Steve. Is it correct to assume that Squier and the asian sizes are 6mm with metric thread ?
Dave Robinson
-
dave robinson
-
- Posts: 5949
- Joined: Wed Sep 09, 2009 2:34 pm
- Location: Sheffield
- Full Real Name: David Robinson
-
by Uncle Fiesta » Mon Apr 06, 2020 12:36 pm
I believe so, but need more research before giving a definitive answer!
-
Uncle Fiesta
-
- Posts: 1189
- Joined: Fri Apr 27, 2012 11:31 pm
- Location: near Gainsborough, England
- Full Real Name: Steve Tebble
by chas » Mon Apr 06, 2020 7:42 pm
Mex Strats are 5mm (though I think some early ones may have been 10/32").
Squiers have been 5mm or 6mm depending on which factory was making at the time. Nowadays there seem to be far more 5mm. (An exeption is probably the original JV models which featured some US factory supplied hardware).
I'm saying this from workshop experience and what over the counter customers have needed.
Chas.
-
chas
-
- Posts: 288
- Joined: Wed Sep 16, 2009 12:20 pm
- Location: Croydon
- Full Real Name: Chas de Lacy
-
by RogerCook » Tue Apr 07, 2020 9:00 pm
M5 and 10-32 threads are very similar. If you express the pitch and diameter in the same measurement units, M5 is 5mm diameter whereas 10-32 is 4.7625. Threads per inch, 10-32 is 32tpi and M5 is 31.75tpi. So both will "fit" the other but not perfectly because of the slight size differences and different thread forms.
Last edited by
RogerCook on Wed Apr 08, 2020 11:45 am, edited 1 time in total.
-
RogerCook
-
- Posts: 498
- Joined: Thu Sep 17, 2009 9:56 am
- Full Real Name: Roger Cook
by dave robinson » Tue Apr 07, 2020 11:05 pm
So if there is a deficit in the fit, then won't one into the other will strip it out eventually?
Dave Robinson
-
dave robinson
-
- Posts: 5949
- Joined: Wed Sep 09, 2009 2:34 pm
- Location: Sheffield
- Full Real Name: David Robinson
-
by RogerCook » Wed Apr 08, 2020 7:50 am
Possibly Dave. I've heard of metric arms used to tighten a worn block thread!
-
RogerCook
-
- Posts: 498
- Joined: Thu Sep 17, 2009 9:56 am
- Full Real Name: Roger Cook
by Uncle Fiesta » Sat Apr 11, 2020 4:36 pm
Yes, in my experience a 5mm arm will go into a 10/32 block - for about a turn or so, then it locks up.
Screwing any harder will risk damage.
(That's funny, that's what she said to me last night ...)
-
Uncle Fiesta
-
- Posts: 1189
- Joined: Fri Apr 27, 2012 11:31 pm
- Location: near Gainsborough, England
- Full Real Name: Steve Tebble
Return to Gear
Who is online
Users browsing this forum: No registered users and 62 guests